111 lines
2.8 KiB
Arduino
111 lines
2.8 KiB
Arduino
|
#include <Wire.h>
|
||
|
|
#include <Adafruit_Sensor.h>
|
||
|
|
#include <Adafruit_BNO055.h>
|
||
|
|
#include <utility/imumaths.h>
|
||
|
|
|
||
|
|
/* This driver reads raw data from the BNO055
|
||
|
|
|
||
|
|
Connections
|
||
|
|
===========
|
||
|
|
Connect SCL to analog 5
|
||
|
|
Connect SDA to analog 4
|
||
|
|
Connect VDD to 3.3V DC
|
||
|
|
Connect GROUND to common ground
|
||
|
|
|
||
|
|
History
|
||
|
|
=======
|
||
|
|
2015/MAR/03 - First release (KTOWN)
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* Set the delay between fresh samples */
|
||
|
|
#define BNO055_SAMPLERATE_DELAY_MS (100)
|
||
|
|
|
||
|
|
Adafruit_BNO055 bno = Adafruit_BNO055();
|
||
|
|
|
||
|
|
/**************************************************************************/
|
||
|
|
/*
|
||
|
|
Arduino setup function (automatically called at startup)
|
||
|
|
*/
|
||
|
|
/**************************************************************************/
|
||
|
|
void setup(void)
|
||
|
|
{
|
||
|
|
Serial.begin(9600);
|
||
|
|
Serial.println("Orientation Sensor Raw Data Test"); Serial.println("");
|
||
|
|
|
||
|
|
/* Initialise the sensor */
|
||
|
|
if(!bno.begin())
|
||
|
|
{
|
||
|
|
/* There was a problem detecting the BNO055 ... check your connections */
|
||
|
|
Serial.print("Ooops, no BNO055 detected ... Check your wiring or I2C ADDR!");
|
||
|
|
while(1);
|
||
|
|
}
|
||
|
|
|
||
|
|
delay(1000);
|
||
|
|
|
||
|
|
/* Display the current temperature */
|
||
|
|
int8_t temp = bno.getTemp();
|
||
|
|
Serial.print("Current Temperature: ");
|
||
|
|
Serial.print(temp);
|
||
|
|
Serial.println(" C");
|
||
|
|
Serial.println("");
|
||
|
|
|
||
|
|
bno.setExtCrystalUse(true);
|
||
|
|
|
||
|
|
Serial.println("Calibration status values: 0=uncalibrated, 3=fully calibrated");
|
||
|
|
}
|
||
|
|
|
||
|
|
/**************************************************************************/
|
||
|
|
/*
|
||
|
|
Arduino loop function, called once 'setup' is complete (your own code
|
||
|
|
should go here)
|
||
|
|
*/
|
||
|
|
/**************************************************************************/
|
||
|
|
void loop(void)
|
||
|
|
{
|
||
|
|
// Possible vector values can be:
|
||
|
|
// - VECTOR_ACCELEROMETER - m/s^2
|
||
|
|
// - VECTOR_MAGNETOMETER - uT
|
||
|
|
// - VECTOR_GYROSCOPE - rad/s
|
||
|
|
// - VECTOR_EULER - degrees
|
||
|
|
// - VECTOR_LINEARACCEL - m/s^2
|
||
|
|
// - VECTOR_GRAVITY - m/s^2
|
||
|
|
imu::Vector<3> euler = bno.getVector(Adafruit_BNO055::VECTOR_EULER);
|
||
|
|
|
||
|
|
/* Display the floating point data */
|
||
|
|
Serial.print("X: ");
|
||
|
|
Serial.print(euler.x());
|
||
|
|
Serial.print(" Y: ");
|
||
|
|
Serial.print(euler.y());
|
||
|
|
Serial.print(" Z: ");
|
||
|
|
Serial.print(euler.z());
|
||
|
|
Serial.print("\t\t");
|
||
|
|
|
||
|
|
/*
|
||
|
|
// Quaternion data
|
||
|
|
imu::Quaternion quat = bno.getQuat();
|
||
|
|
Serial.print("qW: ");
|
||
|
|
Serial.print(quat.w(), 4);
|
||
|
|
Serial.print(" qX: ");
|
||
|
|
Serial.print(quat.y(), 4);
|
||
|
|
Serial.print(" qY: ");
|
||
|
|
Serial.print(quat.x(), 4);
|
||
|
|
Serial.print(" qZ: ");
|
||
|
|
Serial.print(quat.z(), 4);
|
||
|
|
Serial.print("\t\t");
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* Display calibration status for each sensor. */
|
||
|
|
uint8_t system, gyro, accel, mag = 0;
|
||
|
|
bno.getCalibration(&system, &gyro, &accel, &mag);
|
||
|
|
Serial.print("CALIBRATION: Sys=");
|
||
|
|
Serial.print(system, DEC);
|
||
|
|
Serial.print(" Gyro=");
|
||
|
|
Serial.print(gyro, DEC);
|
||
|
|
Serial.print(" Accel=");
|
||
|
|
Serial.print(accel, DEC);
|
||
|
|
Serial.print(" Mag=");
|
||
|
|
Serial.println(mag, DEC);
|
||
|
|
|
||
|
|
delay(BNO055_SAMPLERATE_DELAY_MS);
|
||
|
|
}
|